NSR25S

N-CAS® NSR25S 25mm Aperture Normally Open Uni-Stable Shutter

Vincent Associates, the manufacturer of UNIBLITZ® shutters has again endeavored to provide an even more reliable shutter product for the Photonics industry with the introduction of the 25mm aperture version of the patented N-CAS® (Non-Contact Actuation System) shutter, the NSR25S (additional patents pending on this technology). The device’s reliability has been enhanced by significantly reducing the number of moving parts. In the 25mm aperture normally open uni-stable version, the NSR25S, there are a total number of six moving parts, five of which are the blades themselves! The activating mechanism is non-contact and has shown to increase its reliability through testing over similar shutter designs.

The NSR25S is a uni-stable shutter, power is required to hold the shutter in the closed state. Once power is removed the shutter will return to the open state on its own.  There are no dimensional changes associated with this configuration and it can be driven by the VDM1000.  This device can also be configured normally closed, please see the NS25S.

Another advantage of the NSR25S is the ease of which it can be installed in a customer application since the only protruding part from the surface of the shutter are the actuator coils.  The remainder of the structure is thin and flat to allow easy integration without the concern for external moving parts.

The NSR25S can be actuated by user supplied driver circuits or the VDM1000, a new driver built specifically to take advantage of the NS25S’s low power requirements. This new driver will permit the NSR25S to operate with virtually identical open and close times since it provides a power assisted return.

When gating high intensity light sources, the NSR25S can be equipped with reflective blades. This option protects the shutter blades from the light source’s damaging effects by reflecting the energy away from the blade surface. Three standard reflective blade options are available - “S” (reflective stainless steel), “Z” (AlSiO) and “ZM” (AlMgF2).

The standard shutter is terminated by a 5-pin male connector with 6 inch cable assembly. The 510A cable is required when controlling the NSR25S with the VDM1000. This cable is included with the VDM1000. There is an access slot located above the actuator that will allow for manual operation of the shutter if so desired.

FEATURES

FEATURES

• Patented N-CAS® actuator system radically reduces moving parts.
• Additional patent applications pending on this technology.
• Uni-stable design requires power when holding the device in the closed state.
• Also available in a normally closed configuration, the NS25S.
• Simple design provides maximum clearance around the aperture.
• Machined flat surfaces for easy integration into virtually any system.
• Small form factor, 25mm aperture, 2.250 inch overall diameter.
• Reflective blades available for high energy light sources.
• Terminated to 6 inch 5-pin male connector harness or 18 inch flying leads.

Electrical

¹ Voltage level required across actuator coil when being held in the open position.

Mechanical

¹ CONTinuous frequency rating specified at shutter’s minimum exposure pulse. BURST frequency rating specified for (4) four seconds maximum with (1) one minute minimum between bursts. Frequency measurements are taken in free air, 25°C ambient, actuator coil equipped with heat sink. For additional information on maximum sustained frequencies obtainable, please contact one of our technical representatives.

Uni-Stable (Normally Closed)

Timing

The following chart lists typical timing values (msec.) using UNIBLITZ® drive equipment and measured with UNIBLITZ® shutters equipped with standard black Teflon® coated shutter blades.

The question regarding enhancement of shutter speed with the application of user supplied lubricants has been repeatedly asked. It is our experience that lubricating the shutter blades will actually slow the shutter down and eventually render the shutter inoperable. UNDER NO CIRCUMSTANCES SHOULD ANY TYPE OF LUBRICANT BE APPLIED TO THE SHUTTER BLADE AREA.

All timing specification were measured using the N-CAS® VDM1000 Drive Controller.

Unhoused Style

The UNIBLITZ® II NSR25S is designed with a low-profile and flat surfaces for easy integration into your system. Hole locations are identical to the current CS25 as well as an additional set of mounting holes to provide supplementary installation options. The body of the shutter measures 2.25” in diameter and only .20” thick. The only protrusion from his envelope is the small actuator and hold down bracket which have a clearance of .71” from the center of the aperture.

The NSR25S will be actuated by the VDM1000, a new driver built specifically to take advantage of the NS25’s low power requirements. This new driver will permit the NS25 to operate with virtually identical open and close times.

Part Number Example

NSR25S 1 T 0 L

^* Input side only, black coating is on opposite side. Intended to protect the shutter blade surface. The light source must be input to the reflective side only.