Electrical Comparison Chart
The Electrical Chart compares the electrical specifications of all standard UNIBLITZ type shutters. Devices shown will not use the same type drivers. Please see individual device specification for recommended electronic driver units. UNIBLITZ electronic drive equipment converts line voltage to that necessary to operate all UNIBLITZ shutters. If you plan to design your own driver it is highly recommended that you contact one of our technical representatives or see our Custom Capabilities page for additional information.
| SERIES |
COIL RESISTANCE |
PULSE VOLTAGE TO OPEN |
HOLD VOLTAGE1 (NOMINAL) |
| CS25 |
12 OHMS |
+65 VDC |
+5 VDC |
| CS35 |
12 OHMS |
+70 VDC |
+7 VDC/+5VDC2 |
| CS45 |
12 OHMS |
+70 VDC |
+7 VDC/+5VDC2 |
| CS65 |
12 OHMS |
+70 VDC |
+7 VDC/+5VDC2 |
| CS90HS |
24 OHMS Primary3
|
+70 VDC Primary
|
+7VDC/+5VDC2 Primary
|
| |
24 OHMS Secondary3
|
+70 VDC Secondary
|
+7VDC/+5VDC2 Secondary
|
| DSS10 |
8 OHMS |
+10.7 VDC |
N/A |
| DSS20 |
8 OHMS |
+10.7 VDC |
N/A |
| DSS25 |
7.5 OHMS |
+10.7 VDC |
N/A |
| LS2 |
48 OHMS |
+65 VDC |
+10 VDC |
| LS3 |
48 OHMS |
+65 VDC |
+10 VDC |
| LS6 |
48 OHMS |
+65 VDC |
+10 VDC |
| NS15B |
24 OHMS |
+36 VDC |
N/A |
| NS25B |
6 OHMS |
+36 VDC |
N/A |
| NS25S |
12 OHMS |
+36 VDC |
+5 VDC |
| NS35B |
12 OHMS |
+36 VDC |
N/A |
| NS45B |
24 OHMS (each coil) |
+36 VDC |
+5 VDC |
| NS65B |
24 OHMS |
36 VCD |
|
| NSR25S |
12 OHMS |
+36 VDC |
+5 VDC |
| TS2S |
8 OHMS |
+10.7 VDC |
3VDC |
| TS6B |
8 OHMS |
10.7 VDC |
N/A |
| VS14 |
12 OHMS |
+65 VDC |
+5 VDC |
| VS25 |
12 OHMS |
+65 VDC |
+5 VDC |
| VS35 |
12 OHMS |
+70 VDC |
+7VDC/+5VDC2 |
| XRS14 |
12 OHMS |
+65 VDC |
+5 VDC |
| XRS25 |
2 OHMS |
+65 VDC |
+5 VDC |
| XRS6 |
12 OHMS |
+65 VDC |
+10 VDC |
1 Voltage level required across actuator coil when being held in the open position
2 Dual hold voltage level driver system included in UNIBLITZ VMM/VCM shutter control
3 Actuators are wired in parallel. Combined DCR is 12 ohms.