| The following provides additional information on the Electronic Synchronization System, Cable/Adapter/Connector Layout, and our Manufacturer's Warranty.
ELECTRONIC SYNCHRONIZATION SYSTEM
The Electronic Synchronization System provides a feedback signal after the shutter transfers to the open state. The system incorporates an infrared emitting diode, an infrared sensitive detecting transistor, and an interrupting vane. The vane is attached to the shutter so as to block the light path between the emitter and detector in the closed position. When the shutter transfers to the 80% open position, the vane is removed from the infrared light path, allowing the emitter to switch the detector to the active state. See Figure #1 for the CS25 and CS35 schematic with the Electronic Synchronization system. See Figure #2 for the QCS45 schematic with the Electronic Synchronization system. See Figure #3 for the CS25/CS35/QCS45 schematic without the Electronic Synchronization. See figure #4 for the schematic of all other shutter models (except CS90) with Electronic Synchronization. See Figure #5 for the schematic of all other shutter models (except CS90) without Electronic Synchronization. Support circuitry for the Electronic Synchronization System is built into the VCM and VMM type drive equipment. See the Timing section's Figure 1 for typical synchronization output waveform in the timing specifications.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
CABLE-ADAPTER-CONNECTOR LAYOUT:
Figure 6
Drawing showing connector layout and termination for an un-housed or housed shutter style configuration.
SHUTTER INTERCONNECTING CABLE TYPES:
710P Cable - 7-pin WirePro in-line female connector to 7-wire flying leads, 10ft. length. Supplied with D880C OEM driver or can also be purchased separately for use with 122-BP OEM driver.
710C Cable - 7-pin WirePro in-line female connector to 7-pin WirePro in-line male connector. 10ft.length. Presently supplied with VMM-D3, VMM-D4 OR VMM-T1 drivers. 710A will replace the 710C at a future date. (701CR Adapter may be required at that time.) The 710C can be purchased separately.
710B Cable - (7-pin WirePro in-line female connector to 7-pin ODU push-lock in-line male connector. Length is (3) meters. Presently supplied with the VCM-D1 driver. The 710A will replace the 710B at a future date. (701CR Adapter may be required at that time.) The 710B can be purchased separately.
710A Cable - 7-pin WirePro in-line female connector to 5-pin SWITCHCRAFT locking in-line male connector. Length is (3) meters. The 710A will replace the 710C and the 710B at a future date. The 710A can be purchased separately.
SHUTTER INTERCONNECTING ADAPTER TYPES:
501A-S7 Adapter - 5-pin SWITCHCRAFT locking in-line female connector to WIREPRO 7-pin in-line male connector. Length is (8) inches. Supplied with CS25, CS35 and QCS45 shutters which are equipped with 5-pin male connectors.
701CR Adapter – 7-pin WirePro in-line female connector to 7-pin WirePro in-line male connector. Length is (8) inches. Used if an older shutter with a 7-pin male connector and electronic synchronization is used with a newer type controller and the controller is supplied with a 710A interconnect cable. The 701CR adapter has a resistor installed in the female connector to bias the electronic sync emitter. Without this adapter the electronic sync will not function when using the 710A cable.
WARRANTY
All products manufactured by VINCENT ASSOCIATES are warranted to meet published specifications and to be free of defects in materials and workmanship as defined in the specifications for 365 (one year) days from the date of original shipment. MANUFACTURER will, at its own option, repair or replace without charge any listed item discovered to be defective excepting transportation charges. Burned out or otherwise damaged actuator coils are not covered under this warranty.
The buyer’s exclusive remedy and the limit of MANUFACTURER’S liability for any loss whatsoever shall not exceed the purchase price paid by the buyer for the goods to which a claim is made. MANUFACTURER does not give any implied warranties of merchantability, fitness for a particular purpose, or of any other nature in connection with the sale of any products.
The MANUFACTURER will consider the return of unused equipment if returned within 30 days from the original date of shipment, subject to a 20% restocking charge. This offer does not apply to used or damaged equipment. This warranty extends only to the original purchase and is not available to any third party, including any purchaser assemblies or other products of which the goods may become component equipment.
This warranty does not extend to cover damage resulting from alteration, misuse, negligence, abuse, normal wear and tear, or accident. | 
Home
What's New
Contact Us
Related Links
Site Map
